Even if you have not stinted on quality windows foam seat cushions and correctly calculated operati

Despite some flaws plastic windows, foam seat cushions their dignity can rate each citizen: They are not allowed in the apartment street noise, soot and dust (especially important for industrial and central areas of the city); Once installed they do not need to be painted; They were easy to care for, and unlike wood, they are not afraid of moisture; Install windows significantly cheaper than high quality window frames made of wood. Key Features of windows with plastic is heat and sound insulation; ventilation; foam seat cushions security;
Panoramic windows installation of plastic windows service life and how you will be satisfied with them, depends foam seat cushions not only on quality but also on the conformity of a model conditions of your home.
If you interfere with most street noise, the emphasis will have to do for sound insulation and use at least two-chamber package; for residents of lower floors or the latest special importance level of protection glass and so on. d. What matter?
Even if you have not stinted on quality windows foam seat cushions and correctly calculated operating conditions, they still need to successfully install. Incorrect or careless installation will negate foam seat cushions all their advantages and disadvantages will increase. Tools and materials
You also need to buy a few cans foam; Anchor bolts (eg 10 mm x 180 mm); stands; wooden shims; panels and corners for slopes; sealant or liquid plastic tube in ptastikovoy.
Do not skimp on the mounting foam: poor quality foam will give good insulation, because inside the cavity left after zapenivaniya, foam seat cushions and some species after dry crumble. Procedure Remove the old window, remove the leaf from its hinges, remove the trim and remove the window box. With crowbar lift ebb and external sill (sill-concrete in older homes can not be dismantled) and remove the window frame of the hole. If necessary vidbyyte old slopes - you may have to expand the hole. Prepare to window installation, foam seat cushions remove the sash and glazing beads, remove the glass from the frame. Many manufacturers recommend that before installing completely remove the protective film from the profile, but master practitioners are advised not to rush with this, not to povdedit profile during operation. Set the window frame in the window opening. Planting depth Defaults for all types of wall and glass - it is 1/3 the thickness of the wall. If you violate this policy will accumulate between the glass condensate. foam seat cushions Keep in mind that the frame should be at a level not "in the hole"! Horizon Lines aperture is not always strictly horizontal, and even invisible to the eye slant break functionality mechanics window. The horizontal level window frame usually govern through a special substrate under windows. Move the frame horizontally, while the gap between foam seat cushions the frame and the wall will not be the same. It is desirable that their width does not exceed three inches, otherwise it will be difficult to close the foam. Vertical level assigned using wooden wedges or special Pidstavochnyy plates.
To do this without removing the frame from the hole in the right places, make a pencil mark on it, then it can be removed and drill holes. The distance foam seat cushions between anchors should not be more than 70 inches, and the distance from the inner corner to the hole in the recommended range of 10-15 cm (as the distance from the inside foam seat cushions of the frame profile to the bar or bolt). Now it's time to finally fix the frame in the cut. This is done - and vertically and horizontally - the same wedge-struts that you used in the "first fitting." Where are fitted plugs, place wooden blocks to frame in driving the anchor is not pressed against the wall. Inside the frame through the holes in it carefully drill corresponding holes in the wall and install anchor bolts. The slots between the frame and the wall around foam seat cushions the perimeter Load foam. That she held tight, wet the surface of the wall. Different types of foam using unequally increase its volume, and they had to clean off excess before applying read the instructions foam seat cushions on the containers. Install sill. Sills made on the size of the window opening and attached to it using parts that are assembled to Pidstavochnyy profile window. Having got him in the window frame, canvas equalize the level by using a substrate (eg 10-mm insulated sandwich panels), special supports or wedges that hold him tightly to the bottom of the frame. Note that it is heated by the window frame by about two inches, so after installation foam seat cushions will be narrower than the cut-blank canvas. The space under the sill sometimes closed up mortar, but usually it is filled with foam (it should come partly at low tide to Pidstavochnyy account has been closed completely). On the windowsill put loads of at least 10-15 kilograms, or expanded foam can pick it up. Outflow box mounted outside foam seat cushions Cons